@prefix vivo: . @prefix edm: . @prefix ns0: . @prefix dcterms: . @prefix skos: . vivo:departmentOrSchool "Science, Faculty of"@en, "Earth and Ocean Sciences, Department of"@en ; edm:dataProvider "DSpace"@en ; ns0:identifierCitation "Deng, Xingxiu, Stull, Roland B. 2005. Mesoscale Analysis Method for Surface Potential Temperature in Mountainous and Coastal Terrain. Monthly Weather Review. 133(2) 389-408."@en ; ns0:rightsCopyright "Stull, Roland B."@en ; dcterms:creator "Deng, Xingxiu"@en, "Stull, Roland B."@en ; dcterms:issued "2011-04-11T20:07:31Z"@en, "2005-02"@en ; dcterms:description """A technique is developed to anisotropically spread surface observations in steep valleys. The goal is to create an improved objective analysis for the lowest, terrain-following numerical weather prediction (NWP) model level in mountainous terrain. The method is a mother–daughter (MD) approach, where the amount of information transferred from one grid point (the mother) to all neighboring grid points (the daughters) depends on elevation differences. The daughters become mothers and further share information with their neighboring grid points. This iterative method allows information to follow valleys around ridges, while reducing spread over the ridge top. The method is further refined to account for land–sea anisotropy. This approach is tested in the objective analyses of surface potential temperatures over the steep mountainous and coastal terrain of southwestern British Columbia, Canada. Analysis results are compared with other existing schemes using the Advanced Regional Prediction System Data Assimilation System (ADAS). It is found that the MD approach outperforms the other schemes over mountainous and coastal terrain. Copyright 2005 American Meteorological Society (AMS). Permission to use figures, tables, and brief excerpts from this work in scientific and educational works is hereby granted provided that the source is acknowledged. Any use of material in this work that is determined to be “fair use” under Section 107 of the U.S. Copyright Act or that satisfies the conditions specified in Section 108 of the U.S. Copyright Act (17 USC §108, as revised by P.L. 94-553) does not require the AMS’s permission. Republication, systematic reproduction, posting in electronic form, such as on a web site or in a searchable database, or other uses of this material, except as exempted by the above statement, requires written permission or a license from the AMS. Additional details are provided in the AMS Copyright Policy, available on the AMS Web site located at (http://www.ametsoc.org/) or from the AMS at 617-227-2425 or copyright@ametsoc.org."""@en ; edm:aggregatedCHO "https://circle.library.ubc.ca/rest/handle/2429/33533?expand=metadata"@en ; skos:note """A Mesoscale Analysis Method for Surface Potential Temperature in Mountainous and Coastal Terrain XINGXIU DENG AND ROLAND STULL University of British Columbia, Vancouver, British Columbia, Canada (Manuscript received 20 December 2003, in final form 19 July 2004) ABSTRACT A technique is developed to anisotropically spread surface observations in steep valleys. The goal is to create an improved objective analysis for the lowest, terrain-following numerical weather prediction (NWP) model level in mountainous terrain. The method is a mother–daughter (MD) approach, where the amount of information transferred from one grid point (the mother) to all neighboring grid points (the daughters) depends on elevation differences. The daughters become mothers and further share information with their neighboring grid points. This iterative method allows information to follow valleys around ridges, while reducing spread over the ridge top. The method is further refined to account for land–sea anisotropy. This approach is tested in the objective analyses of surface potential temperatures over the steep moun- tainous and coastal terrain of southwestern British Columbia, Canada. Analysis results are compared with other existing schemes using the Advanced Regional Prediction System Data Assimilation System (ADAS). It is found that the MD approach outperforms the other schemes over mountainous and coastal terrain. 1. Introduction Objective analysis transforms information from ran- domly spaced observing sites into data at regularly spaced grid points (Krishnamurti and Bounoua 1996). It is often done by optimally combining observations and a short-range NWP forecast, called a first guess (background). Analysis schemes, such as optimum in- terpolation (OI) (Daley 1991), successive corrections (Bratseth 1986), and 3D variational analysis (Laroche et al. 1999), require the specification of a covariance function to model the spatial correlations of back- ground errors. The background error covariance, used to define the optimum weights for data spreading, is often assumed to be isotropic. Isotropy, however, is a questionable assumption for mesoscale analyses or for analyses in mountainous/ coastal regions. Therefore, flow-dependent or anisotro- pic covariance models are receiving more attention, such as by introducing isentropic (Benjamin et al. 1991) or semigeostrophic (Desroziers 1997) coordinate trans- formations in analysis increments. Flow-dependent background error covariance can also be estimated ex- plicitly by Kalman filtering (KF), implicitly by 4D variational data assimilation (4DVAR) methods, or ap- proximated in the ensemble Kalman filter (EnKF) (Gauthier et al. 1993; Bouttier 1993; Thépaut et al. 1996; Houtekamer and Mitchell 1998, 2001). But KF, 4DVAR, and EnKF are computationally time consum- ing. Lanzinger and Steinacker (1990) incorporated anisotropic correlation structures due to orography, to resolve sharp gradients across major mountain ridges (Alps, Pyrrenees). Miller and Benjamin (1992) used el- evation differences in correlation functions to account for terrain effects. Present computing power allows fine-grid NWP models to resolve small mesoscale flows within indi- vidual valleys. Such resolution is important, because in steep mountainous terrain the valleys contain most of the population centers, industries, and transportation routes. To this end, the Mesoscale Compressible Com- munity (MC2) model (Benoit et al. 1997; Laprise et al. 1997) has been running daily for several years at the University of British Columbia (UBC). MC2 is a fully compressible model using semi-implicit semi- Lagrangian techniques. Currently, the daily forecasts at UBC start with 108-km grid spacing, initialized from the Eta analysis, and then one-way nest down to 36, 12, 4, and 2 km. The two finest grids can resolve different weather in separate neighboring valleys. Accurate fine- resolution forecasts depend on accurate and represen- tative initial fields from which to start. This study fo- cuses on the surface data analysis at the lowest, terrain- following MC2 model level. Corresponding author address: Xingxiu Deng, Dept. of Earth and Ocean Sciences, University of British Columbia, 6339 Stores Rd., Vancouver, BC V6T 1Z4, Canada. E-mail: xdeng@eos.ubc.ca FEBRUARY 2005 D E N G A N D S T U L L 389 © 2005 American Meteorological Society MWR2859 The Advanced Regional Prediction System (ARPS) (Xue et al. 2000) Data Assimilation System (ADAS) (CAPS 1995; Brewster 1996) in ARPS5.0.0 Beta8 is used as an analysis tool. The ADAS employs the suc- cessive-correction method of Bratseth (1986), requiring less computational time than other advanced methods (i.e., KF and 4DVAR). This allows near-real-time, high-resolution analysis over most of British Columbia (BC), Canada, using moderately powerful computers. In the mountainous terrain of western North America, many surface observation sites are located in deep valleys. Both the background error covariance and representativeness of surface observations are af- fected by heterogeneous terrain. BC has a variety of landscapes from seashores, straits, and fjords to moun- tains and valleys. Some valleys are narrow and long with kinks and twists. The need for weather data at many sites in a valley is often not matched by the avail- ability of weather stations. Typically, villages are strung along valley floors, with ski resorts higher up the slopes and reservoirs in tributary valleys. Observations from a surface weather station at one village in the valley is often not representative of conditions up- or downval- ley nor is it representative of conditions on nearby mountain slopes. Similarly, weather observations at ridge top would not be representative of surface weather in the adjacent valley. This typical scenario stimulates the following ques- tion. At locations (in that one valley) distant from the observation station, which of the following better rep- resents the initial air state: 1) the first guess (from a previous high-resolution forecast) or 2) the observa- tions from the distant station? An experiment to ad- dress this question would be to densely instrument the valley, and to determine the correlations. However, it is likely that the conclusions would apply only to that one valley. It might also be risky to apply results from other densely instrumented valleys (e.g., the Mesoscale Al- pine Project) to the valleys in BC. Within the constraints of the present numerical ex- periments, we hypothesize that in a serpentine valley, the first guess (from a fine-resolution NWP model) is better than a distant observation from the same valley, in the absence of dense intravalley observations. This hypothesis herein is referred to as the intravalley decor- relation assumption. An extension of this hypothesis treats two valleys separated by a high ridge and herein is referred to as the intervalley decorrelation assump- tion. If there is an observation in only one valley, then the first guess in the noninstrumented valley represents the air state better than the observation from the other valley. We implement the intravalley and intervalley decor- relation hypotheses within the ADAS Bratseth scheme for data assimilation in complex terrain. The intravalley assumption uses a Gaussian drop-off with distance from the observation, where distance is measured along the circuitous path of the valley. The intervalley assump- tion uses an anisotropic term that reduces data spread- ing into terrain of differing elevation. A mother–daughter (MD) approach is proposed here to calculate the anisotropic term and circuitous travel distance (CTD). The anisotropic effect is introduced via a “sharing factor,” namely, the fraction of informa- tion shared between an observation and analysis grid point (GP). Near coastlines, land–sea anisotropy is also included. Section 2 describes the ADAS, and modifications for this study. Section 3 reviews basic concepts of atmo- spheric boundary layers (BLs) in mountainous terrain. The MD approach is presented in section 4. Numerical experiments are given in section 5. In section 6, with case examples we demonstrate characteristics and ad- vantages of the MD approach over two other schemes. Computational costs are also examined. Summary and discussions are in section 7, and a sensitivity analysis is in the appendix. 2. The analysis tool a. General description The ADAS was developed by the Center for Analy- sis and Prediction of Storms (CAPS, University of Oklahoma). It is a 3D mesoscale analysis system that ingests and analyzes meteorological data from different observational sources. The ADAS is efficient, easily implemented and attractive for high-resolution analysis on model levels. The ADAS combines observations with a first guess using the Bratseth (1986) scheme, which converges to OI. Like OI, the Bratseth scheme accounts for the rela- tive error between the observations and the first guess. Different from OI, this scheme iterates without the in- version of large matrices, and requires less computer resources. The ADAS has gained wide usage in research and operational forecasting. Research applications for a strong cold-front passage (Ciliberti et al. 1999) and sen- sitivity experiments (Ciliberti et al. 2000) showed that realistic local and mesoscale structures can be analyzed with the aid of local data. Operational applications in- cluded short-range weather forecasts over east-central Florida (Case et al. 2002), weather support for the 2002 Winter Olympics (Horel et al. 2002), and near-real-time applications to complex terrain in the western United States (Lazarus et al. 2002). Lazarus et al. (2002) intro- duced into the ADAS a terrain factor for surface data.1 The terrain factor affects only the analysis in the free atmosphere. 1 This was expanded for 3D data (surface and sounding data) by Keith Brewster (CAPS 2004, personal communication) in a newer version (ARPS5.1.0). 390 M O N T H L Y W E A T H E R R E V I E W VOLUME 133 b. Modifications 1) ADAS VERSUS MC2 GRIDS For better analysis quality, analyses are performed directly on the MC2 grid using MC2 output as first- guess fields. 2) QUALITY CONTROL For surface observations, quality control includes cli- matological checks, temporal checks, horizontal consis- tency checks [Barnes (1964) technique], and observa- tion-to-background difference checks. For case studies with virtual observations (section 6a), no quality control is needed. For case studies with real observations (section 6b), the horizontal consis- tency checks and observation-to-background difference checks are turned off for the following reasons. The Barnes technique does not work well for quality control of fine-resolution data in complex terrain, because any one surface observation might not be represented well by nearby observations at different elevations or on the opposite side of a mountain range. In steep terrain, the observation-to-background difference might be large due to a discrepancy between the actual station eleva- tion and the model GP elevation, rather than due to bad quality of the surface observation. We have re- duced the ADAS trilinear interpolation to bilinear when the first-guess fields are interpolated to the ob- servation locations. The ADAS trilinear interpolation algorithm causes large interpolation errors by introduc- ing “free-atmosphere” background values (Lazarus et al. 2002); also, the algorithm causes large extrapolation errors for the surface valley stations far below the low- est model level. Because the objective quality-control methods are problematic in steep mountains, we instead do subjec- tive examinations on observation minus background re- siduals (not shown). 3) ANISOTROPIC CORRELATION FUNCTION The ADAS Bratseth scheme works iteratively, up- dating the first guess using the difference between the observed values and observational estimates derived from the analysis (CAPS 1995; Lazarus et al. 2002). The optimum Bratseth weights rely on the correlation () of the background errors (and on the ratio of observation error variance to background error variance). Over flat terrain, a Gaussian function [G(d)] is frequently used to smoothly reduce the correlation with distance (d), caus- ing the impact of a single observation to be isotropic in the grid space around the observation [(d)  G(d)]. In mountainous terrain, we modify the Gaussian drop-off to be a function of the CTD (s, defined in section 4) from the observation to an analysis point [(s)  G(s)]. As discussed in section 1, the correlation should be weighted by an anisotropic term (S) that is a function of the difference between elevations of the observation (Zo) and the analysis point (Za). By sepa- rating horizontal and vertical effects into two factors, an anisotropic correlation becomes s  Gs  SZo, Za. 1 An MD approach is proposed in section 4 to generate S and s for each observation station. This approach is based on first-order BL characteristics in mountainous terrain, described next. 3. Topographic anisotropy and boundary layers a. First-order boundary layer characteristics in mountainous terrain Atmospheric BLs always contain air of colder poten- tial temperature than the air higher in the free atmo- sphere (FA), because the average troposphere is stably stratified (Stull 1988, 2000). Between the BL and FA is a strongly stable layer that caps the BL. Trapped in the BL below this cap are pollutants, humidity, and heat released from the surface. In steep mountains, the ridge heights above valley floors are frequently the same order as BL heights. To a zeroth order, the turbulent and advective communi- cation of physical, dynamic, and chemical states be- tween one valley and the other depends greatly on whether the BL is shallower than the surrounding ridges. For shallow BL situations, tracers emitted into one valley BL are unlikely to reach neighboring valleys, due to blocking by mountains. For situations with BLs deeper than ridges, BL air can mix between neighbor- ing valleys. To a first order, the BL top (zi) is often not level over complex terrain. Observations show a variety of behav- iors, ranging from BLs that follow the topography to BLs that seem relatively level (Lenschow et al. 1979; De Wekker et al. 1997; Kalthoff et al. 1998; Kossmann et al. 1998). Stull (1992) identified four archetypical BL-top characteristics (Fig. 1). Gravitational forces tend to make a level BL top (Fig. 1c), much like an ocean surface that is level over undersea mounts. Other factors including entrainment, advection, and friction tend to make a terrain-following top (Fig. 1b). See Stull (1998) for a similarity-theory analysis of the competing factors. We will focus on the level and terrain-following cases (Fig. 2). BL parameterizations in most NWP models do not provide information on levelness of the BL top within first-guess fields for use during data assimilation. Nor are observations of BL depth usually available at every surface weather station. In an attempt to compensate for the lack of information, we develop a background error correlation () that includes weighting factors for both “level-top” and terrain-following BL effects. Namely, we define the sharing factor SF [S in (1)] dur- ing one iteration by FEBRUARY 2005 D E N G A N D S T U L L 391 Sod  1  Som  WTFBL  1,   WLTBL  1, 2 where subscript o represents the observation, subscripts m and d represent a GP (mother) and its neighboring GP (daughter), respectively. Weights W represent the portions of the SF associated with terrain-following BLs (TFBLs) or level-top BLs (LTBLs). b. Parameterization of terrain-following and level-top BL contributions Let Z be elevation. Approximate the terrain- following BL effects on the SF, from one mother GP during iteration  to a neighboring daughter GP at it- eration   1, by WTFBL  1,   1 |Zm Zd  1 |zref1 a 3 for |Zm() Zd(  1) | zref1; otherwise WTFBL  0. The terrain-following BL-depth parameter is zref1, while parameter a controls the analysis decorrelation rate. For illustration, suppose that zref1  1 km and a  1. Let the weather station be collocated with a model GP (the first mother GP) at the base of linearly sloping terrain (Fig. 2a) such that each successive daughter GP is higher up the slope: z()  0, 0.5, 1.0, 1.5 km . . . for   0, 1, 2, 3. . . . The iteration counter () coincides with each successive daughter GP. The resulting se- quence of weights from (3) is WTFBL  1.0, 0.5, 0.5, and 0.5. These weights accumulate multiplicatively via the iteration given by (2). Considering only terrain- following effects, S(0)  1, S(1)  0.5, S(2)  0.25, and S(3) 0.125. The GP at Z 1.5 km has nonzero SF, for the case of a terrain-following 1-km-thick BL, where turbulence can mix valley variables up the mountain slope. Similarly, we can define a level-top BL weight by WLTBL  1  1 |Zo Zd  1 |zref2 b 4 for |Zo Zd(  1) | zref2; otherwise WLTBL  0. The level-top BL-depth parameter is zref2, while pa- rameter b controls the analysis decorrelation rate. For illustration with the same sloping GPs as in the previous example, suppose that zref2  1 km and b  1. The resulting sequence of weights from (4) is WLTBL  1.0, 0.5, 0., and 0. These weights accumulate multi- plicatively via iteration as in (2). If we neglect the ter- rain-following effects, S(0)  1, S(1)  0.5, S(2)  0., and S(3)  0. The GP at Z  1.5 km has zero SF, because it is above the level BL top (Fig. 2b). At all FIG. 1. Archetypical categories of mixed-layer-top levelness (af- ter Stull 1992). (a) Hyper terrain following; (b) terrain following; (c) level; (d) contra-terrain following. FIG. 2. Shallow boundary layers in steep terrain, for (a) a ter- rain-following boundary layer and (b) a level-top boundary layer blocked by mountains. White dots represent surface grid points. The iteration counter  coincides with each successive daughter grid point. The lowest grid point at   0 is collocated with the surface weather station. 392 M O N T H L Y W E A T H E R R E V I E W VOLUME 133 higher-elevation GPs, the SF is also zero. Those points higher on the mountain are assumed to be in a different air mass than the valley station. It is worth noting that zref2 is essentially the BL depth at the observation lo- cation. It will be shown later in the appendix that analy- sis results are far more sensitive to zref2 than to zref1. These illustrations, albeit somewhat primitive, repre- sent basic BL characteristics in a way that allows aniso- tropic correlations to be created, as shown next. 4. The mother–daughter approach a. General concepts We first consider a surface observation that happens to lie directly on a model GP. The fraction of informa- tion shared between the observation and any analysis point is called “sharing factor” (SF), which ranges be- tween 0 and 1. Let subscripts o, m, and d represent an observation, a mother GP and a neighboring daughter GP, respectively. The iterative MD approach is ex- pressed by Sod  1  Som1 |Zm Zd  1 |zref1 a  1 |Zo Zd  1 |zref2 b if |Zm Zd  1 |  zref1 and |Zo Zd  1 |  zref2 5a Sod  1  0 if |Zm Zd  1 |  zref1 or |Zo Zd  1 |  zref2, 5b where  is iteration counter; Z is elevation; and a, b, zref1, and zref2 are free parameters. The amount of information that a mother transfers to each daughter is reduced by the elevation difference between them. The iteration starts with Som(0)  1 at the surface observa- tion location. As previously discussed, the first and sec- ond bracketed terms in Eq. (5a) contain the terrain- following [WTFBL in Eq. (3)] and level-top [WLTBL in Eq. (4)] BL effects, respectively. The observation is treated as the first mother, who has daughters at each of her eight neighboring GPs. This is the first iteration (  1). These daughter SFs are calculated by applying (5) to every mother– daughter pair. The circuitous travel distance from the observation to a neighboring daughter GP, after   1, is equal to the straight-line horizontal distance if the SF at that daughter GP is not zero. For zero SF, the CTD is assigned a large value (s  1.0e5 km), so that (s) in (1) is zero due to the Gaussian drop-off. Namely, the observation has no influence on that GP. Next, every daughter becomes a mother and has her own eight daughters around her, and so on (see below). Around any daughter might be several mothers who contribute different SFs to that daughter, but only the biggest SF (among all values from neighboring mothers and the value from the previous iteration) is kept. Thus, Eq. (5) has to be applied successively to every GP within a gradually enlarged subdomain centered at the observa- tion location. This process is computationally expen- sive, as demonstrated in section 6b. From the second iteration onward, the CTD from the observation to any daughter GP is found by accumulating the incremental path segments from each successive mother to the daughter GP. Usually there are many different paths from the observation to a distant GP, but the path saved is the one with the largest SF at that daughter GP. Figure 3 illustrates the CTD (s) from the observation “O” to GP “D.” To illustrate calculations of the SFs and CTDs, con- sider a surface station that happens to lie directly on a model GP at (x, y)  (7, 5) (Figs. 4 and 5, indicated by a solid triangle). Horizontal grid spacing is 3 km. Ini- tially, the SF is 1.0 at the observation location, and zero elsewhere (left-hand panel of Fig. 4a). The CTD is ini- tially 0 km at the observation point and 1.0e5 km oth- erwise (right-hand panel of Fig. 4a). The SFs and CTDs after the first iteration are shown in Fig. 4b. The CTD for a daughter GP remains 1.0e5 km if its SF is 0. Thus, the CTD (s) from the observation to the GP at (8, 5) is 1.0e5 km, even though the straight-line horizontal dis- tance (d) is 3 km. A daughter GP with nonzero SF has finite CTD [e.g., s  d 4.2 km for GP (6, 6)]. In the second iteration, each daughter becomes a mother and has her own eight daughters around her, yielding 24 (816) daughters after   2 (Fig. 4c). This process is repeated until |Sod (  1) Sod() | 0.01 for all GPs. The final SFs (Sod) and CTDs (s) are used in (1) to determine the anisotropic correlation function [(s)]. Figure 5 shows the end results for this hypothetical sta- FIG. 3. Schematic of the straight-line horizontal distance (d) and the circuitous travel distance (s  d1  d2  d3) from the obser- vation location O to the grid point D, after the third iteration. The grid point D received the most contribution in its sharing factor from the grid point B, while the grid point B received the most contribution from the grid point A that received the most contri- bution from the observation O. This illustrates a situation such as when a mountain (indicated by shading) lies between O and D. FEBRUARY 2005 D E N G A N D S T U L L 393 FIG. 4. (left column) Printed values of the sharing factors (zeroes are not printed except when they first appear in an iteration; darker shading indicates higher elevations) and (right column) circuitous travel distance (km) (large values of 1.0e5 are not printed). (a) iteration counter   0; (b)   1; (c)   2. The observation is indicated by a solid triangle at (x, y)  (7, 5). Grid spacing is 3 km. The parameters used are a  2, b  2, zref1  750 m, and zref2  750 m. Grid cells along the outside edge are cut off in this plot but are really the same size as all other grid cells. 394 M O N T H L Y W E A T H E R R E V I E W VOLUME 133 tion, using a Gaussian drop-off with a standard devia- tion of 30 km. To examine the subtleties of the CTD, consider GP (6, 5) in Fig. 4. After   1, S  0.31 and s  3 km (Fig. 4b). Obviously, the SF comes from the first mother (i.e., the observation). After   2, S  0.38 and s 7.2 km (Fig. 4c). Now the largest SF comes from a second- generation mother GP (6, 4). The CTD (s 7.2 km) equals the sum of d 4.2 km between the observation and the second-generation mother GP (6, 4), plus d  3 km from GP (6, 4) to the target GP (6, 5). Parameters a and b in (5) control SF reduction by the mother–daughter GP elevation difference. As a and b are reduced from 4 toward 1, the terrain effects on the analysis increase. The optimum values of a, b, zref1, and zref2 can be obtained by analyzing a subset of the available observations, and verifying against the re- maining observations for a substantial period of daily analyses, assuming a dense observation network. For fixed GPs and observation locations within a model domain, the SFs and CTDs for each observation station can be determined. In the case of a surface ob- servation station that is not collocated with a model GP, the station is first approximated as being collocated at the nearest neighboring model GP with minimum el- evation difference between them. The resulting SFs and CTDs are saved as a fixed file, which can be applied unchanged for each day’s analysis to efficiently deter- mine the correlation in the ADAS Bratseth scheme. In the presence of temporally missing observations, a flag (i.e., 999.) can be assigned to the missing observa- tions. The SFs and CTDs for a newly added surface station can be calculated and appended to the fixed file. b. Refinement for coastal terrain To consider land–sea contrasts, Hessler (1984) esti- mated two correlation functions from surface tempera- ture statistics near the Baltic Sea. Between pairs of sea stations or pairs of land stations, he approximated cor- relations by exp( 0.08d0.13) cos(0.4d). Between sea and land stations, he used exp( 0.29d0.06)cos(0.2d). We introduce a similar approach by including an ad- ditional factor (i.e., the third term in brackets on the right-hand side): Sod LS  1  Som LS 1 |Zm Zd  1 |zref1 a  1 |Zo Zd  1 |zref2 b  1 |LSo LSd  1 |KLS  6 for |Zm() Zd(  1) | zref1 and |Zo Zd(  1) | zref2; otherwise SLSod(  1)  0. The land–sea mask LSo at the observation location is equal to one for a land observation and zero for a water observation. The land–sea mask LSd at a daughter GP is similar, but averaged over the nine GPs immediately around and including the daughter GP. The average allows gradual transition of the SFs across the coastlines in an attempt to slightly account for sea/land breeze effects. Param- eter KLS controls the degree of the decorrelation be- FIG. 5. (top) Sharing factor isopleths (thin lines, after a Gaus- sian drop-off with standard deviation of 30 km) and (bottom) the circuitous travel distance (km) for an idealized observation in valley A within a horizontal domain that spans 36 km  36 km with a grid increment of 3 km. Terrain elevations (m) are shown by shading in the top plot. Darker shading indicates higher eleva- tions, with a maximum terrain-height difference of 2000 m. The observation is indicated by a solid triangle at (x, y)  (7, 5). The parameters used are a 2, b 2, zref1 750 m, and zref2 750 m. FEBRUARY 2005 D E N G A N D S T U L L 395 tween land stations and analysis points over water, or between water stations and analysis points over land; KLS was subjectively set to 1.0 for the case studies in section 6b, but could be greater than 1.0 for strong sea-breeze events. Ideally, the location of the land–sea mask should shift as the sea/land breezes evolve every day; however, we neglect this shift. This allows a computationally ef- ficient constant land–sea mask that still captures first- order effects. 5. Numerical experiments Four assimilation experiments (Table 1) are per- formed for comparison purposes. GAUSS, the native scheme in the ADAS (ARPS5.0.0 Beta8), includes ter- rain effects with a Gaussian function of elevation dif- ference ( z) between the GP and observation station, and horizontal Gaussian decay to define the region of influence. In experiment TERR_DIFF, the Miller and Benjamin (1992) method is added to the ADAS, but slightly modified from the original correlation function2 for potential temperature used in Miller and Benjamin (1992). In experiment MD, the SFs from Eq. (5) are used to replace the Gaussian elevation term in GAUSS. MD further differs from GAUSS and TERR_DIFF by using the CTD, rather than the straight-line horizontal dis- tance, in the horizontal part of the correlation function. This effectively limits the region of influence in com- plex terrain and restricts valley observation information to follow the valleys around the ridges, while reducing spread over the ridge top. Similarly, ridge-top informa- tion follows ridges, with little spread into valleys. MD_LSMG is the same as MD except that land–sea anisotropy is included in the SFs (section 4b). Unless stated specifically, the horizontal correlation length scale (Rh) is 90 km for the first and second Brat- seth passes, 60 km for the third pass, and 30 km for the fourth and fifth passes. 6. Case studies The utility of the MD approach is demonstrated be- low for surface potential-temperature analyses in two regions. Virtual and real observations are used for mountainous and coastal terrains, respectively, in southwestern BC. a. Virtual observations We first use “fraternal-twin” experiments to evaluate the MD approach in mountainous terrain. In fraternal- twin experiments, the “truth” and “analysis” models are similar, but not identical (Arnold and Dey 1986). The truth model (MC2 at 2-km grid spacing) is first integrated 12 h to generate a reference truth atmo- sphere. To generate a different first guess, the analysis model (MC2 at 3 km with radiation turned off to pur- posely introduce errors) is integrated 12 h with the same boundary conditions, but using perturbed initial conditions. Amplitudes of random perturbations for temperature (u wind, v wind, logarithm of pressure per- turbation, specific humidity) are 5.0°C (5.0 kt, 5.0 kt, 0.0005, 0.005 kg kg 1). A dynamic initialization algo- rithm built into MC2 is activated for the 3-km run to remove spurious gravity waves excited by the added perturbations. The fraternal-twin experiments are performed for 7–8 March 2003, characterized by an Arctic outbreak, when cold shallow air masses from northern Canada swept into the valleys in BC. The MC2 runs consist of five self-nested grids with grid spacings of 108, 36, 12, 4, and 2 or 3 km (see the last three grids in Fig. 6). The Eta analysis and forecasts at 90.7-km grid spacing from the National Centers for En- vironmental Prediction (NCEP), valid at 0000 UTC 7 March 2003, are used as the initial and boundary con- ditions for the coarsest grid. The MC2 at 2 km is started at 1200 UTC 7 March from MC2 4-km output and in- tegrated 12 h to generate the truth atmosphere, from which virtual surface observations are extracted. All virtual observations are assumed to be perfect, with zero observation error. The MC2 at 3 km is also started at 1200 UTC 7 March, but from the randomly per- turbed output of the 4-km run, and integrated 12 h to 2 exp( | d |2/2r2)/(1  Kz · | z|2), r  300 km, Kz  7  10 7m 2. TABLE 1. Experiments performed, where Rh and Rz are corre- lation length scales in the horizontal and vertical, respectively, which define the regions of influence; dij and zij are straight-line horizontal distance and elevation difference between an analysis grid point and the observation station, respectively; Kz is a coef- ficient; sij is the circuitous travel distance from the observation to an analysis grid point determined in the mother–daughter pro- gram; Sod is the sharing factor at an analysis grid point, which represents how much the analysis grid point shares the observa- tion information; SLSod is the same as Sod except that the former is from the refined mother–daughter approach. In this study, Rh is 90 km for the first and second iterations, 60 km for the third iteration, and 30 km for the fourth and fifth iterations, during the ADAS assimilation cycle. Experiment Correlation function () GAUSS exp 12 | dij | 2Rh2  · exp 12 |zij| 2 Rz 2  TERR_DIFF exp 12 | dij | 2Rh2 1  Kz · |zij|2 MD exp 12 sij2Rh2 · Sod MD_LSMG exp 12 sij2Rh2 · SodLS 396 M O N T H L Y W E A T H E R R E V I E W VOLUME 133 provide a first guess. The analyses are performed at the lowest terrain-following model level of the MC2 3 km at 0000 UTC 8 March. Figure 7 shows six virtual surface stations. Stations o1 (elevation 920 m) and o2 (elevation 536 m), located in different valleys, are used for analysis. Station o1 is in the Elaho River Valley, and o2 is in the Lillooet River Valley. Four stations (b1, b2, b3, and b4) in the Lillooet River Valley are used for verification. These stations are selected to evaluate the impact of observation o1 on the neighboring Lillooet River Valley. Elevations for stations b1, b2, b3, and b4 are 894, 881, 765, and 830 m, respectively. 1) IMPACT OF A SINGLE VALLEY SURFACE OBSERVATION For objective analysis, the interpolated first guess is usually subtracted from the observation to give an “ob- servation increment,” which is analyzed to produce “analysis increments” (AIs) at the GPs. The final analy- sis at each GP is then the first guess plus the analysis increment. The AIs produced by o1 show how data are spread to surrounding GPs. Figure 8 shows the impact of o1 on the GP analysis. The observation increment is 3.35 K. The Bratseth analysis is confined to a single pass for convergence in the presence of a single perfect observation. All experi- ments show that the observation mostly influences the valley GPs. GAUSS and TERR_DIFF both yield large AIs in valleys disconnected from the Elaho River Valley, even though both valleys may not necessarily share the same air mass. The Lillooet River Valley (containing b1, Fig. 7) is such an example. In MD, the large AIs are in the Elaho River Valley (containing o1), with much smaller values in the Lillooet River Valley. 2) IMPACT OF TWO SURFACE OBSERVATIONS FROM DIFFERENT VALLEYS The analysis at one GP using observations from ad- jacent but disconnected valleys, where each valley con- tains a different meteorological regime, is a problem in complex terrain. To examine this, consider two obser- vations in different valleys (stations o1 and o2 in Fig. 7). The observation at o1 is 3.35 K colder than the first guess, while the observation at o2 is 3.36 K warmer. Four stations (b1, b2, b3, and b4) in the Lillooet River Valley are used to verify the analyses. First, only the observation at o2 is used. To evaluate the three schemes, the GP analyses are interpolated to the four verifying stations (not collocated with any GP) by cubic polynomial interpolation. The root-mean- square error (rmse) between the observations and analyses at those sites are calculated. For comparison purposes, the parameters for GAUSS (Rz  500 m), TERR_DIFF (Kz  7.0  10 6 m 2), and MD (a  2, b  2, zref1  750 m, zref2  750 m) are chosen so that the three schemes produce similar rmses. The values of these parameters are kept fixed for all subsequent ex- periments. Rmses for GAUSS, TERR_DIFF, and MD are 0.6179, 0.6468, and 0.6559 K, respectively. Rmses for these three schemes are slightly greater than that be- tween the observations and the first guess, which is FIG. 6. MC2 grid domains for 4, 3, and 2 km. MC2 4-km output provides nesting files to initialize 2- and 3-km runs. MC2 2 km is run to provide a reference atmosphere to generate virtual surface observations for analysis and verification. MC2 3 km is run to provide first-guess fields for analysis. FIG. 7. Virtual surface observation stations, indicated by solid triangles, used in the analysis and verification. The stations are positioned at the truth-model terrain height in the Coast Moun- tains north of Vancouver. Station o1 (50.326°N, 123.578°W) is near the mouth of the Elaho River. Station o2 (50.3344°N, 122.767°W) is near the town of Pemberton. Terrain elevations (m) are from the truth model. Darker shading indicates higher eleva- tions, with a maximum elevation difference of 2055 m in this figure. FEBRUARY 2005 D E N G A N D S T U L L 397 0.5395 K. The analyses and the first guess versus the observations for the three schemes are shown in the left-hand panel of Fig. 9. It is evident that the three schemes produce similar analyses. The observations from both sites (o1 and o2) are then used to produce an analysis. While the same set of observations at b1, b2, b3, and b4 are used for verifi- cation. The additional observation at o1 has a negative impact on both the GAUSS and TERR_DIFF analyses (see the right-hand panel of Fig. 9). Rmse increases to 2.1464 K for GAUSS and 2.4380 K for TERR_DIFF. However, in MD, the additional observation at o1 has a minor impact on the analysis at the verifying stations, as desired because the two valleys with observations are not strongly coupled. The slight influence from the added observation reduces the rmse to 0.4807 K. The rmse with two observations is reduced about 11% from the first guess. 3) IMPACT OF A SINGLE HIGH-ELEVATION SURFACE OBSERVATION In complex terrain, most surface observation sites are located in densely populated valleys. There are, how- ever, some surface stations located at high elevations in the mountains, such as at ski areas and in subalpine forest ecosystems. This subsection examines the analy- sis impact of high-elevation observations. Figure 10 shows the AIs produced by o3 (elevation 1954 m). The observation increment is 1.56 K. All schemes produce minimal spread into valley GPs, with MD producing zero spread into the valleys. For GAUSS and TERR_DIFF, the observation in- crement is spread to all of the surrounding high moun- tains, including those separated by deep valleys. In MD, the observation corrects the first guess only for those GPs on the same mountain as o3. The GAUSS and TERR_DIFF analyses in Fig. 10 look more realistic than MD for two reasons. During shallow cold-air pool- ing events, the high-mountain tops are all penetrating into the free atmosphere, where they would experience the same weather. Second, during deep BL events with BL top above the mountain top, vigorous turbulence would also cause mixing across the valleys. In future work, we plan to modify MD to allow such spreading. b. Real observations The MD approach is also tested with real observa- tions in the coastal terrain of the Georgia Basin, BC. Hourly data are combined from several agencies, in- cluding the BC Ministry of Transportation and High- ways (MOTH), BC Ministry of Water Land and Air Protection (WLAP), Environment Canada (EC), and BC Hydro (HYDR). The higher density of observa- tions over the Georgia Basin (Fig. 11) allows us to with- hold some for verification (Table 2). The land–sea mask is based on the model-resolved coastlines. The ratio of observation-error variance to background-error variance is 0.08 as in Miller and Benjamin (1992). The low observation-to-background error implies that the observations are heavily weighted. A 3–4 February 2003 case, characterized by a strong ridge over the Georgia Basin, is used to examine if weak land–sea thermal contrasts can be properly ana- lyzed. Figure 12 shows the evolution of potential tem- peratures for several surface stations on land and water FIG. 8. Analysis increments (isopleths) for potential tempera- ture at the lowest model level in response to a single surface potential-temperature observation at station o1 indicated by a solid triangle. Contour interval is 0.3 K. Darker shading indicates higher elevations, with a maximum elevation difference of 1940 m, which is less than that in Fig. 7 because of the smoothed terrain used in the NWP model. (top) GAUSS; (middle) TERR_DIFF; (bottom) MD. 398 M O N T H L Y W E A T H E R R E V I E W VOLUME 133 during 0000–1200 UTC 4 February 2003. In late after- noon at 0000 UTC (1600 PST), all land stations except Vancouver INTL ARPT were slightly warmer than the water stations. After a transition period from 0100 to 0300 UTC, all land stations were colder than the water stations. Land–sea thermal contrast is the most promi- nent in early morning at 1200 UTC (0400 PST). The Eta analysis and forecasts from NCEP, valid at 0000 UTC 3 February 2003, are used to drive the coars- est grid (108-km grid spacing), which in turn drives grids of 36, 12, and 4 or 3 km. MC2 at 3 km provides first-guess fields and is started at 1200 UTC 3 February from MC2 4-km output. Analyses are performed every hour from 0000 to 1200 UTC 4 February, by blending hourly surface observations with the first guess at the lowest terrain-following model level valid at the same FIG. 9. Analysis, indicated by a circle, and first guess, indicated by a plus, vs observation. (left column) Observation at o2 only is used in the analysis. (right column) Observations at both o1 and o2 are used in the analysis. (top) GAUSS; (middle) TERR_DIFF; (bottom) MD. The four points (circles or pluses) correspond to the four verifying stations b1–b4. FEBRUARY 2005 D E N G A N D S T U L L 399 time. The hourly analyses are not incorporated into the forecast cycle; thus, each analysis is independent of past observations. Eight stations are used for analysis and 11 others for verification (Table 2), but the available num- ber of reporting stations varies with the analysis time (Table 3). Figure 13 shows time series of the first guess (FSTG) or the analyzed potential temperature and observations for one water station (Entrance Island) and one land station (White Rock), separately. The 3-km run pro- duces a good first guess for White Rock from 0300 to 1200 UTC 4 February, but underpredicts the potential temperatures for Entrance Island. The analyses from all experiments show more agreement with the obser- vations than the first guess. Comparatively, MD and MD_LSMG both produce better analyses than GAUSS and TERR_DIFF. MD_LSMG is superior in maintain- ing the thermal contrast between Entrance Island and White Rock. Figure 14 further demonstrates advan- tages of MD_LSMG, based on separate averages from three land and three water stations. Averaging all land stations, including the mountain stations, makes the land–water contrast very small. However, advantages of MD_LSMG can be seen from separate averages of all water stations and all land stations except the moun- tain stations (not shown). The verification statistics (Table 4) show that all schemes improve FSTG as measured by bias, mean ab- solute error (mae), and normalized root-mean-square error (nrmse). TERR_DIFF is slightly better than GAUSS, with smaller mae and nrmse. MD is better than GAUSS and TERR_DIFF, and MD_LSMG is the best. Percentage improvement of rmse over FSTG is below 40% for GAUSS and TERR_DIFF but above 50% for MD and MD_LSMG. Compared to MD, MD_LSMG gains 5% more improvement. To compare computational efficiency, each experi- ment is performed on one processor of a High- Performance Computing Linux Super-Cluster, with 1-GHz Pentium III CPU. The results from a surface- only analysis at 0100 UTC 4 February 2003 are pre- sented in Table 5. For the purpose of computational comparison, all 169 available temperature observations are used within a domain having 257  205  52 685 GPs, with 3-km grid spacing. The execution time for GAUSS is slightly less than that for TERR_DIFF. The execution time for the MD approach is split into two parts: 1) the calculation of the SFs (which needs to be done only once for each surface station within an analy- sis domain, as mentioned in section 4a) and 2) the ap- plication of the SFs during the analysis (which is re- peated for each analysis). Part 1 of both MD and MD_LSMG is computationally more expensive com- pared to GAUSS and TERR_DIFF, while part 2 is nearly the same as TERR_DIFF. MD_LSMG is com- putationally cheaper than MD, because adding land– water contrasts limits the region of influence and hence speeds convergence. The timing for part 1 is done with- out limiting the observation’s influence region. Thus, the computational costs are affected by the domain size. To eliminate the domain-size effect, the SFs are cal- culated within an influence region (a square here) of the observation. The radius of the circle inscribed in the square was set to 300 km, which is slightly greater than the radius of influence (ROI; 273.14 km) calcu- lated in the ADAS based on Rh for the first pass. Now the execution time for calculating the SFs is reduced 36.5% for MD and 33% for MD_LSMG [see item (*) in Table 5]. FIG. 10. Analysis increments (isopleths) for the potential tem- perature at the lowest (terrain-following) model level in response to a single high-elevation observation at o3, indicated by a white solid triangle on the mountain top. Contour interval is 0.2 K. Darker shading indicates higher elevations (m). (top) GAUSS; (middle) TERR_DIFF; (bottom) MD. 400 M O N T H L Y W E A T H E R R E V I E W VOLUME 133 FIG. 11. The northern half of the Georgia Basin area. The surface stations are shown by pluses, below which are station IDs. Station information is in Table 2. The bottom plot is zoomed to the top center of the top plot. Terrain elevations (m), indicated by shading, are from unsmoothed terrain data resolved by the NWP model at 3-km grid spacing. Darker shading represents higher elevations, with a maximum elevation difference of (top) 1374 m and (bottom) 1200 m. FEBRUARY 2005 D E N G A N D S T U L L 401 7. Summary and discussion An MD approach and its shoreline refinement are proposed for surface-data analysis on terrain-following surfaces in mountainous/coastal terrain. The resulting SFs and CTDs are then incorporated into the ADAS. For the cases examined here, the new scheme is com- pared with the original scheme (GAUSS) in the ADAS (ARPS5.0.0 Beta8), and the scheme (TERR_DIFF) de- veloped by Miller and Benjamin (1992). It is found that the MD approach can better account for both terrain- height and valley differences in the analysis of obser- vation increments over mountainous regions. The re- fined MD approach can further account for land–sea contrasts and is recommended for use in mountainous, coastal terrain such as southwestern BC. The one-time, initial computational cost of the MD approach is greater than that of either GAUSS or TERR_DIFF because of the need to calculate the SFs. However, for any fixed set of the free parameters, the resulting SFs can be saved as a fixed file and can be applied unchanged for each day’s analysis. The results from the real-observation case might be further improved if the land/sea-breeze frontal location is used to define the edges of the land mask, rather than the actual coastline. However, determining the position of a sea/land-breeze front increases the complexity and requires that the SFs be recomputed during every analysis. The real-data case shows encouraging results FIG. 12. Observed potential temperature (derived from ob- served temperature) for stations over water (lines with open circles) and over land (lines with filled circles) during 0000–1200 UTC 4 Feb 2003. Stations over water are Entrance Island (620, solid line), Pam Rocks (615, dashed line), and Sand Heads CS (671, dotted line). Stations over land are West Vancouver (673, solid line), Vancouver INTL ARPT (597, dashed line), and White Rock (674, dotted line). Breaks in the graph denote periods for which no observations were reported. 0000 UTC corresponds to 1600 PST (late afternoon), and 1200 UTC is 0400 PST (early morning). TABLE 3. Number of reporting stations for analysis and verification at each analysis time on 4 Feb 2003. No. of stations Time (UTC) Analysis Verification 0000 8 11 0100 8 11 0200 8 11 0300 8 11 0400 4 7 0500 7 11 0600 6 11 0700 7 11 0800 7 11 0900 7 11 1000 7 11 1100 7 11 1200 7 11 TABLE 2. Surface stations for analysis and verification. Station IDs are from the Emergency Weather Net database. For the land–sea (LS) mask, 1 stands for land and 0 corresponds to ocean or water. Full name Station ID Lat (N) Lon (W) Elevation (m) Agency LS Purposes Port Mellon 38 49.5228° 123.4822° 3 WLAP 1 MT Strachan 132 49.4167° 123.2000° 1420 MOTH 1 Gold CK 417 49.4472° 122.4750° 794 HYDR 1 Abbotsford ARPT 604 49.0333° 122.3667° 58 EC 1 Analysis Saturna Island 621 48.7833° 123.0500° 24 EC 0 Pitt Meadows 641 49.2000° 122.6833° 5 EC 1 Point Atkinson CS 654 49.3333° 123.2667° 35 EC 0 Nanaimo ARPT 582 49.0500° 123.8667° 28 EC 1 Crofton 59 48.8803° 123.6458° 20 WLAP 0 Harmac Pacific 61 49.1353° 123.8475° 23 WLAP 0 Deeks Peak 117 49.5333° 123.2167° 1280 MOTH 1 MT Strachan Precip 138 49.4044° 123.1911° 1220 MOTH 1 Vancouver INTL ARPT 597 49.1833° 123.1833° 2 EC 1 Pam Rocks 615 49.5000° 123.3000° 10 EC 0 Verification Discovery Islands CS 617 49.4167° 123.2333° 15 EC 1 Entrance Island 620 49.2167° 123.8000° 3 EC 0 Sand Heads CS 671 49.1000° 123.3000° 15 EC 0 West Vancouver 673 49.3333° 123.1833° 178 EC 1 White Rock 674 49.0167° 122.7667° 13 EC 1 402 M O N T H L Y W E A T H E R R E V I E W VOLUME 133 for the MD approach, even with land–water contrasts fixed at the coastlines. To use the MD approach in mountainous/coastal ter- rain, fine-resolution NWP models (i.e., x 5 km) are recommended, for two reasons. First, the SF is a func- tion of the elevations of analysis GPs; thus, there is a need to resolve all important ridges and valleys. Sec- ond, the quality of the analyses in data-sparse ridges or valleys depends strongly on the quality of the first guess from the NWP models. The MD technique is developed under the intraval- ley and intervalley decorrelation assumptions. None- theless, one can imagine scenarios where the observa- tion in one valley might happen to be well correlated with the air state in a neighboring valley. During a fair- weather event with strong solar heating, the BL could be deeper than the mountain-ridge height, allowing tur- bulence to mix air between the two valleys. Or during strong synoptic forcing, high winds and intense turbu- lence could inject similar air into both valleys and/or homogenize the air in both. For these situations, run- ning the forecast model after initialization will mix the air in neighboring valleys due to resolved advection and parameterized turbulence, even if the initialization spreads the observations only within one valley. Sensitivity tests on the MD free parameters are per- formed for the real-data case (appendix). A subset of available observations are analyzed using various val- ues of the free parameters, and the analyses are verified against the remaining observations. Nrmses are found FIG. 13. Time series of observed potential temperature and the [first guess (FSTG) or analyzed] potential tem- perature from four assimilation experiments for two sta- tions. Observations at Entrance Island over water: dashed line with open triangles. Observations at White Rock over land: dashed line with solid triangles. Analyses at Entrance Island: solid line with open circles. Analyses at White Rock: solid line with filled circles. Analyses are better when the solid lines are closer to the respective dashed lines. FEBRUARY 2005 D E N G A N D S T U L L 403 to be far more sensitive to zref2 than to zref1, and the nrmse sensitivity to zref2 shows a daily cycle, corre- sponding to the characteristics of the BL. This implies that one could automate operationally detecting decor- related weather versus well-mixed events by using ob- served BL depth (if available) as zref2 during daily analyses. Further experiments will be required to inves- tigate the sensitivities for other times and locales. The optimum values of the free parameters might be depen- dent on weather, season, and topography. The results shown here suggest that the free parameters can be determined via sensitivity tests over a substantial pe- riod of daily analyses. For GAUSS and TERR_DIFF, a shorter Rh could be used to successfully reduce the intervalley spreading FIG. 14. Time series of averaged potential temperature of three stations over water and land, respectively. The three stations over water, used for the average, are En- trance Island, Pam Rocks, and Sand Heads CS. West Van- couver, Vancouver INTL ARPT, and White Rock are the three stations used for the average over land. Observations and analyses over water are denoted by the dashed line with open triangles and the solid line with open circles, respectively. Observations and analyses over land are rep- resented by dashed line with solid triangles, and solid line with filled circles, respectively. FSTG stands for the first guess. Closer correspondence between the solid and dashed lines indicate a better analysis. TABLE 4. Verification of analyzed potential temperatures in terms of bias, mean absolute error (mae), and normalized root- mean-square error (nrmse) for all reporting verification stations during the analysis period from 0000 to 1200 UTC 4 Feb 2003. N equals number of stations times the number of observation times. Nrmse is root-mean-square error (rmse) for each experiment nor- malized by the rmse of the first guess (FSTG). Percent improve- ment of the rmse is with respect to FSTG. Experiment N Bias (K) Mae (K) Nrmse (K) Percent improvement FSTG 139 2.6832 2.7624 1.0 0 GAUSS 139 0.5625 1.7565 0.6610 34 TERR_DIFF 139 0.6401 1.6482 0.6317 37 MD 139 0.2344 1.3069 0.4943 51 MD_LSMG 139 0.0051 1.1956 0.4433 56 404 M O N T H L Y W E A T H E R R E V I E W VOLUME 133 from a disconnected neighboring valley (appendix). However, this strategy also reduces the potentially good intravalley spreading. In addition, a universal Rh might be hard to find in highly variable terrain. The MD approach suppresses intervalley spreading while allowing intravalley spreading over a longer distance. This approach automatically accounts for the elevations of surface stations and analysis GPs. The ultimate goal is to provide better input fields for fine-resolution NWP models. To produce improved analyses to drive the MC2, we plan to combine the mesoscale surface analyses from the MD approach with the coarse-resolution Eta analyses from NCEP, and to compare verification statistics with MC2 control runs driven by unmodified Eta initial conditions. We further plan to modify MD to spread free-atmosphere moun- tain-top observations differently than BL valley obser- vations. Acknowledgments. We thank Joshua Hacker from NCAR for his suggestions, and Stephane Chamberland of RPN for MC2 user support. We also thank Henryk Modzelewski, George Hicks, Yongmei Zhou, John Spagnol, and other colleagues at UBC. Thanks also to three reviewers, including Steven Lazarus, John Horel and Keith Brewster. Grant support came from the Ca- nadian Natural Science and Engineering Research Council, the BC Forest Investment Account, Environ- ment Canada (EC), and the Canadian Foundation for Climate and Atmospheric Science. Observation data from the Emergency Weather Net were provided by EC, BC Ministry of Transportation and Highways, BC Ministry of Water Land and Air Protection, and BC Hydro. Geophysical Disaster CFD Center computers were used, funded by the Canadian Foundation for In- novation, the BC Knowledge Development Fund, and UBC. APPENDIX Sensitivity Tests This appendix provides a sensitivity analysis of MD_LSMG to different values of the free parameters for the case from section 6b. The analysis and verifica- tion observations remain the same. This single case is insufficient to determine the optimum values. How- ever, it does indicate some sensitivity characteristics. First, we vary zref1 and zref2 from 250 to 3000 m every 250 m, while holding a  2 and b  2. Recall that zref1 and zref2 are the maximum effective BL heights through which surface observations are felt. Figure A1 shows nrmses versus zref1 and zref2 for TABLE 5. Execution time (s) for each analysis experiment on one processor of a High-Performance Computing Linux Super- Cluster, with 1-GHz Pentium III CPU. The results are obtained from a surface-only analysis at 0100 UTC 4 Feb 2003, when all 169 observations are used for analysis within a domain of 257  205 grid points, with 3-km grid spacing. The parameters used in the mother-daughter approach are a  2, b  2, zref1  750 m and zref2 750 m. For the two MD approaches, item 1 is the one-time setup cost without limiting search radius, item 2 is the execution time for its application to this test domain, and item * is also the one-time setup cost but with limiting search radius to 300 km. Experiment Execution time (s) GAUSS 22.99 TERR_DIFF 28.12 MD (1) 3902.03 (2) 29.96 (*) 2476.80 MD_LSMG (1) 2833.89 (2) 29.93 (*) 1897.60 FIG. A1. Nrmse of analyses vs zref1 and zref2 when a  2 and b  2. Contour interval is 0.025 K. (top) Late afternoon (0000 UTC 4 Feb 2003); (bottom) early morning (1200 UTC 4 Feb 2003). Smaller nrmse is better. FEBRUARY 2005 D E N G A N D S T U L L 405 0000 UTC (1600 PST) and 1200 UTC (0400 PST) 4 February 2003. At both 0000 and 1200 UTC, nrmses are less than 1.0 for any values of zref1 and zref2 within the range 250–3000 m. Thus, the analyses agree with the observations better than the first guess. Nrmse is not sensitive to zref1 when zref1 750 m, or zref2 500 m. This is because the elevation differences between a mother GP and its immediate daughter GPs are usually small. Nrmse is far more sensitive to zref2 than to zref1, as zref2 defines the maximum effective height above the observation, and because the elevation differences between the observation and the analysis GPs vary con- siderably. Figure A1 shows different features at 0000 and 1200 UTC. In late afternoon (0000 UTC), nrmse shows small sensitivity to zref1 750 m and zref2 750 m. In early morning (1200 UTC), lower nrmse is confined to a nar- row band from zref1  500 to 3000 m and from zref2  1000 to 1250 m. Similar sensitivity tests from 0100 to 1100 UTC indicate a transition at 0200 UTC (not shown). The behaviors correspond to the characteris- tics of the evolving BL. Second, we vary a and b from 0.5 to 4.0 every 0.5 for 1200 UTC 4 February 2003. For these experiments, zref1 2250 m and zref2 1000 m, which were the best values from the previous tests. As shown in Fig. A2, a  2 and b  2 (or a  1 and b  2.5) yield lower nrmses. Using the CTD in the MD approach effectively limits the region of influence in complex terrain (section 5). GAUSS and TERR_DIFF ROI sensitivity tests are performed by varying horizontal correlation length scale Rh (used to calculate ROI in the ADAS) from 100 to 10 km every 10 km for the first and second Bratseth passes. For each test, the third Bratseth pass reduces Rh by 70%, while the fourth and fifth passes reduce Rh by 70% from the third pass. For the virtual-observation case (section 6a), rmse decreases rapidly with decreasing Rh for both GAUSS and TERR_DIFF (Fig. A3), as the correction from o1 becomes negligible in the Lillooet River Valley. When Rh  20 km, a minimal rmse is found to be 0.3385 K for GAUSS and 0.4105 K for TERR_DIFF. The rmse with Rh  20 km is reduced about 37% for GAUSS and 24% for TERR_DIFF from the first guess. While such small values of Rh successfully reduce intervalley spreading, they do so at the expense of reducing the potentially good intravalley spreading. The MD approach avoids this problem. FIG. A2. Nrmse of analyses (1200 UTC 4 Feb 2003) vs a and b when zref1  2250 m and zref2  1000 m, which were the best values for 1200 UTC from Fig. A1. Contour interval is 0.025 K. Smaller nrmse is better. FIG. A3. Rmse of analyses (0000 UTC 8 Mar 2003) vs Rh used in the first and second Bratseth passes. The third Bratseth pass has an Rh that is reduced by 70% from the second pass, while the fourth and fifth Bratseth passes have a Rh that is reduced by 70% from the third pass. (top) GAUSS; (bottom) TERR_DIFF. 406 M O N T H L Y W E A T H E R R E V I E W VOLUME 133 Similar tests are performed for the real-observation case (section 6b). Figure A4 shows nrmses versus Rh used in the first and second Bratseth passes for 1200 UTC 4 February 2003. For both GAUSS and TERR_DIFF, nrmses are less than 1.0. Nrmse shows small sensitivity to Rh when Rh 40 km but relatively large sensitivity when Rh 40 km. A minimal nrmse is found at Rh  20 km for GAUSS and at Rh  10 km for TERR_DIFF. Identical tests are performed for 0000 UTC (Fig. A5). Different from the 1200 UTC results, Rh  100 or 90 km produces lower nrmses for both GAUSS and TERR_DIFF. The ROI sensitivity for the real-observation case is much smaller than that for the virtual-observation case. This is not surprising, considering that only two obser- vations in the two adjacent valleys were used for the virtual-observation case. These results indicate that a prescribed Rh does not work everywhere in highly vari- able terrain. An Rh that depends on the elevations of surface stations and analysis GPs might help to improve the analyses from GAUSS and TERR_DIFF. In com- plex terrain, an effective Rh might not only depend on the average station separation, but also on the geo- graphic regions, seasons, and weather. REFERENCES Arnold, C. P., and C. H. Dey, 1986: Observing systems simulation experiments: Past, present, and future. Bull. Amer. Meteor. Soc., 67, 687–695. Barnes, S. L., 1964: A technique for maximizing details in numeri- cal weather map analysis. J. Appl. Meteor., 3, 396–409. FIG. A4. Nrmse of analyses (1200 UTC 4 Feb 2003) vs Rh used in the first and second Bratseth passes. The third Bratseth pass has an Rh that is reduced by 70% from the second pass, while the fourth and fifth Bratseth passes have a Rh that is reduced by 70% from the third pass. (top) GAUSS; (bottom) TERR_DIFF. Smaller nrmse is better. FIG. A5. Same as Fig. A4, but for 0000 UTC 4 Feb 2003. (top) GAUSS; (bottom) TERR_DIFF. Smaller nrmse is better. FEBRUARY 2005 D E N G A N D S T U L L 407 Benjamin, S. G., K. Brewster, R. Brummer, B. Jewett, T. W. Schlatter, T. L. Smith, and P. A. Stamus, 1991: An isentropic three-hourly data assimilation system using ACARS aircraft observations. Mon. Wea. Rev., 119, 888–906. Benoit, R., M. Desgagne, P. Pellerin, S. Pellerin, Y. Chartier, and S. Desjardins, 1997: The Canadian MC2: A semi-Lagrangian, semi-implicit wide band atmospheric model suited for fine- scale process studies and simulation. Mon. Wea. Rev., 125, 2382–2415. Bouttier, F., 1993: The dynamics of error covariances in a baro- tropic model. Tellus, 45A, 408–423. Bratseth, A. M., 1986: Statistical interpolation by means of suc- cessive corrections. Tellus, 38A, 439–447. Brewster, K., 1996: Application of a Bratseth analysis scheme including Doppler radar data. Preprints, 15th Conf. on Weather Analysis and Forecasting, Norfolk, VA, Amer. Me- teor. Soc., 92–95. CAPS, 1995: ARPS version 4.0 user’s guide, Supplement 1: 3-D analysis with ARPS data assimilation system: ADAS version 2.3. Center for Analysis and Prediction of Storms, University of Oklahoma. [Available online at http://www.caps.ou.edu/ ARPS/ADAS.doc.html.] Case, J. L., J. Manobianco, T. D. Oram, T. Garner, P. F. Blottman, and S. M. Spratt, 2002: Local data integration over east- central Florida using the ARPS Data Analysis System. Wea. Forecasting, 17, 3–26. Ciliberti, C. M., J. D. Horel, and S. M. Lazarus, 2000: Sensitivity experiments with a high resolution data assimilation scheme. Preprints, Ninth Conf. on Mountain Meteorology, Aspen, CO, Amer. Meteor. Soc., 413–416. ——, J. D. Horel, and S. M. Lazarus, 1999: An analysis of a cold frontal passage over complex terrain in northwest Utah. Pre- prints, Eighth Conf. on Mesoscale Processes, Boulder, CO, Amer. Meteor. Soc., 459–462. Daley, R., 1991: Atmospheric Data Analysis. Cambridge Univer- sity Press, 457 pp. Desroziers, G., 1997: A coordinate change for data assimilation in spherical geometry of frontal structures. Mon. Wea. Rev., 125, 3030–3038. De Wekker, S. F. J., M. Kossmann, and F. Fiedler, 1997: Obser- vations of daytime mixed layer depths over mountainous ter- rain during the TRACT field campaign. Preprints, 12th Symp. on Boundary Layers and Turbulence, Vancouver, BC, Canada, Amer. Meteor. Soc., 498–499. Gauthier, P., P. Courtier, and P. Moll, 1993: Assimilation of simu- lated wind lidar data with a Kalman filter. Mon. Wea. Rev., 121, 1803–1820. Hessler, G., 1984: Experiments with statistical objective analysis techniques for representing a coastal surface temperature field. Bound.-Layer Meteor., 28, 375–389. Horel, J., T. Potter, L. Dunn, W. J. Steenburgh, M. Eubank, M. Splitt, and D. J. Onton, 2002: Weather support for the 2002 Winter Olympic and Paralympic Games. Bull. Amer. Meteor. Soc., 83, 227–240. Houtekamer, P. L., and H. L. Mitchell, 2001: A sequential en- semble Kalman filter for atmospheric data assimilation. Mon. Wea. Rev., 129, 123–137. ——, and ——, 1998: Data assimilation using an ensemble Kal- man filter technique. Mon. Wea. Rev., 126, 796–811. Kalthoff, N., H.-J. Binder, M. Kossmann, R. Vogtlin, U. Cors- meier, F. Fiedler, and H. Schlager, 1998: Temporal evolution and spatial variation of the boundary layer over complex terrain. Atmos. Environ., 32, 1179–1194. Kossmann, M., R. Vogtlin, U. Corsmeier, B. Vogel, F. Fiedler, H.-J. Binder, N. Kalthoff, and F. Beyrich, 1998: Aspects of the convective boundary layer structure over complex ter- rain. Atmos. Environ., 32, 1323–1348. Krishnamurti, T. N., and L. Bounoua, 1996: An Introduction to Numerical Weather Prediction Techniques. CRC Press, 293 pp. Lanzinger, A., and R. Steinacker, 1990: A fine mesh analysis scheme designed for mountainous terrain. Meteor. Atmos. Phys., 43, 213–219. Laprise, R., D. Caya, G. Bergeron, and M. Giguère, 1997: The formulation of the André Robert MC2 (mesoscale compress- ible community) model. Numerical Methods in Atmospheric and Oceanic Modelling, The André J. Robert Memorial Vol- ume, Atmosphere—Ocean, 195–220. Laroche, S., P. Gauthier, J. St-James, and J. Morneau, 1999: Implementation of a 3D variational data assimilation system at the Canadian Meteorological Center. Part II: The regional analysis. Atmos.–Ocean, 37, 281–307. Lazarus, S. M., C. M. Ciliberti, J. D. Horel, and K. Brewster, 2002: Near-real-time applications of a mesoscale analysis system to complex terrain. Wea. Forecasting, 17, 971–1000. Lenschow, D. H., B. B. Stankov, and L. Mahrt, 1979: The rapid morning boundary-layer transition. J. Atmos. Sci., 36, 2108– 2124. Miller, P. A., and S. G. Benjamin, 1992: A system for the hourly assimilation of surface observations in mountainous and flat terrain. Mon. Wea. Rev., 120, 2342–2359. Stull, R. B., 1988: An Introduction to Boundary Layer Meteorol- ogy. Kluwer Academic, 666 pp. ——, 1992: A theory for mixed-layer-top levelness over irregular topography. Preprints, 10th Symp. on Turbulence and Diffu- sion, Portland, OR, Amer. Meteor. Soc., 92–94. ——, 1998: Studies of mountain climates, and a theory for mixed- layer-top levelness over complex topography. Geophysical Disaster Computational Fluid Dynamics Center Tech. Rep. WFRT-98-001, University of British Columbia, Vancouver, Canada. ——, 2000: Meteorology for Scientists and Engineers. 2d ed. Brooks/Cole, 502 pp. Thépaut, J.-N., P. Courtier, G. Belaud, and G. Lemaitre, 1996: Dynamical structure functions in a four-dimensional varia- tional assimilation: A case study. Quart. J. Roy. Meteor. Soc., 122, 535–561. Xue, M., K. K. Droegemeier, and V. Wong, 2000: The advanced regional prediction system (ARPS)—A multi-scale nonhy- drostatic atmospheric simulation and prediction model. Part I: Model dynamics and verification. Meteor. Atmos. Phys., 75, 161–193. 408 M O N T H L Y W E A T H E R R E V I E W VOLUME 133"""@en ; edm:hasType "Article"@en ; edm:isShownAt "10.14288/1.0041830"@en ; dcterms:language "eng"@en ; ns0:peerReviewStatus "Reviewed"@en ; edm:provider "Vancouver : University of British Columbia Library"@en ; dcterms:publisher "American Meteorological Society"@en ; ns0:publisherDOI "10.1175/MWR-2859.1"@en ; dcterms:rights "Attribution-NonCommercial-NoDerivatives 4.0 International"@en ; ns0:rightsURI "http://creativecommons.org/licenses/by-nc-nd/4.0/"@en ; ns0:scholarLevel "Faculty"@en ; dcterms:title "Mesoscale Analysis Method for Surface Potential Temperature in Mountainous and Coastal Terrain"@en ; dcterms:type "Text"@en ; ns0:identifierURI "http://hdl.handle.net/2429/33533"@en .